Customer Builds: Mazda Sound Deadening Projects
1991 B2600i
Type of Project: Insulating the Car Door for Sound Products Used: 14 sq ft of Damplifier Pro Deadener (Outer Door Skins) Accessories: Wooden Hand Roller
Read more
2002 Sport Wagon
Type of Project: Full Interior Soundproofing Products Used: 114 sq ft of Damplifier Pro Deadener (Floor/Doors/Ceiling/Cargo Area) 72 sqft of Luxury Liner Pro (MLV)(Floor/Doors/Cargo Area) 42 Sq Ft of Mega Zorbe Melamine Foam (Ceiling) Accessories: Spray Adhesive (2 cans), Wooden Hand Roller
Read more
1991 B2200
Type of Project: Cabin Area Products Used: 48 Sq Ft of Damplifier Pro Deadener (Floors/Doors/Back Wall) 32 Sq Ft of Luxury Liner Pro automotive MLV (Floor/Back Wall) 16 Sq Ft of OverKill Pro Closed Cell Foam (Doors) Accessories: Spray Adhesive (2 cans), Speaker Tweakers, Wooden Hand Roller
Read more
2010 Power Hard Top
Type of Project: Replacing Hood Insulation Products Used: 14 sq ft of Damplifier Pro Deadener 16 sqft of Mega Block Thermal Insulation Accessories: Wooden Hand Roller, Foil Tape, Fury Knife
Read more
2017 Mazda 6 Full Soundproofing
Jeffrey H is at it again with another Mazda 6. This time it's a customers vehicle looking for the full, head-to-toe Second Skin treatment. It's round 2 on the same vehicle, so this one should be a breeze right? Knocked it out of the park!! Mazda 6 trunk view with light up subs... very nice!!! Mazda 6 trunk before all of the high quality American made Second Skin It's coming to life while getting more dead! (bad joke?) Just took 30 sqft of Damplifier Pro on the trunk and wheel well humps. Mazda 6 rear deck with about 8 sqft of Damplifier Pro to kill the vibrations Mazda 6 doors before the Second Skin goes in. The metal was just washed with denatured alcohol. It's so fresh and clean looking with that Damplifier skinned on the outer door skins. No tacky billboard logo to be found. Next up is about 8 sqft of OveKill on the door panels. Jeffrey is all about that closed cell foam. Mazda 6 ceiling before the Damplifier Pro goes in. Jeffrey used our Damplifier Butyl Tape on the roof brace welds to reinforce them before applying the sound deadening. About 22 sqft of Damplifier Pro on the ceiling to stop the flex and strengthen the flimsy roof metal. Finally, the floor gets about 35 sqft of Damplifier Pro followed up with 36 sqft of Luxury Liner Pro to block out the exhaust and drive train noise below. Rear seat floor area after about 14 sqft of Damplifier Pro and 18 sqft of Luxury Liner Pro mass loaded vinyl to block out those unwanted airborne noises.
Read more
Kia Audio Upgrade
This Miata came into Sound Evolution of Texas for a full sound system, sound dampening, and under body lights.This returning client knew what he was looking for and said to do our thing on it. The only thing he was concerned was to do a banging system by being as stealth as possible and not making a bunch of new holes. By using the factory mounts and screw down points we re used those to mount the amp racks.Custom enclosure built in house as well as a speaker housing and grills where the rear panel storage was located.We went with-* Audiomobile subwoofer !✅* Brax, Helix, Match by Audiotec Fischer for all speakers, DSP and amplifiers!✅* Second Skin Audio for all sound dampening materials Damplifier Pro and Luxury Liner Pro!✅* Stinger for under body lights and wiring and accessories!✅* Metra Electronics for wiring and accessories !✅Client was absolutely blown away with the results and dang this thing sounded amazing. Only at Sound Evolution.Miata getting the aduio treatment by Sound EvolutionMiata getting Damplifier Pro and Luxury Liner Pro on the cabin floor.Reinforcing the door panel with Damplifier Pro. Follow up with OverKill Closed Cell Foam.Next up, both the inner and outer skins covered with Damplifier Pro.Check out that outer skin coverage out past the window. Nice work.Finish off with the inner door skin treated with Second Skin Damplifier Pro.
Read more
2016 Mazda 6 Full Vehicle Sq Build
Every now and then Jeffrey has time between his full time job and installing car audio in customer's vehicles to work on his own masterpiece. His 2016 Mazda 6 Sound Quality build has the full Second Skin treatment from head to toe. Jeff ordered the Full Size Sedan Build Package with 80 sqft of Damplifier Pro (CLD) and 54 sqft of Luxury Liner Pro (MLV). Then added 36 sqft of OverKill Pro, 16 sqft of Mega Zorbe, 36 sqft of OverKill, and the Premium Hood Kit. Straight from Jeff... _"Second Skin has always taken care of me on all of my automotive sound deadening needs. This is yet another example. I was concerned with my paint longevity from heat and I had concerns about engine noise when I was doing some more spirited driving. Eric recommended that I use some Damplifier Pro and his new product Mega block to tackle this project. The Mega Nlock product was super easy to use. It cuts like a dream with a fresh razor blade and the adhesive is seriously impressive. Be careful, it sticks to fingers really well also. The results were exactly what I was looking for. My engine noise was reduced and my hood temperature dropped dramatically regardless if it was just sitting in the sun or after my drive home. As always. Great products and customer service Second Skin."_ For more information on a similar build, check out our article on Mazda3 sound deadening. Follow Jeffrey on Instagram to keep up with his journey with dozens of awesome builds! @jeffreyhald
Read moreNo articles found for this topic.